hoi
kann mir jemand sagen wie die belegung bei einem ps pad oder ps2 pad ist ? also welches kabel für welchen knopf ist usw ? =)
brauche das nur vom kabel. ps wäre am besten.
cya + thx
n8bizz
PS2 oder PS Pad-Kabel-Belegung ?
Moderator: Moderatoren
-
- Admin
- Beiträge: 4508
- Registriert: Sa 8. Nov 2003, 00:00
- Wohnort: Lotte / Osnabrück
- Kontaktdaten:
Du meinst die Belegung vom Stecker, den man in die Konsole steckt?
Michael
Code: Alles auswählen
LOOKING AT THE PLUG
-------------------------------
PIN 1->| o o o | o o o | o o o |
\_____________________________/
PIN # USAGE
1. DATA
2. COMMAND
3. N/C (9 Volts unused)
4. GND
5. VCC
6. ATT
7. CLOCK
8. N/C
9. ACK
DATA
Signal from Controller to PSX.
This signal is an 8 bit serial transmission synchronous to the falling edge of clock (That is both the incoming and outgoing signals change on a high to low transition of clock. All the reading of signals is done on the leading edge to allow settling time.)
COMMAND
Signal from PSX to Controller.
This signal is the counter part of DATA. It is again an 8 bit serial transmission on the falling edge of clock.
VCC
VCC can vary from 5V down to 3V and the official SONY Controllers will still operate. The controllers outlined here really want 5V.
The main board in the PSX also has a surface mount 750mA fuse that will blow if you try to draw to much current through the plug (750mA is for both left, right and memory cards).
ATT
ATT is used to get the attention of the controller.
This signal will go low for the duration of a transmission. I have also seen this pin called Select, DTR and Command.
CLOCK
Signal from PSX to Controller.
Used to keep units in sync.
ACK
Acknowledge signal from Controller to PSX.
This signal should go low for at least one clock period after each 8 bits are sent and ATT is still held low. If the ACK signal does not go low within about 60 us the PSX will then start interogating other devices.
Offizieller Ansprechpartner von Step Revolution für den Vertrieb von StepManiaX in Europa.
- Grimmi Meloni
- Admin
- Beiträge: 4430
- Registriert: So 8. Jun 2003, 23:00
- Wohnort: Paderborn
- Kontaktdaten:
für alle die es interessiert, hier die belegung und die farbe von einem
original playstation eins pad. also kabel farbe und funktion.
LOOKING AT THE PLUG
-------------------------------
PIN 1->| o o o | o o o | o o o |
\__________________/
das mit dem bild bekomme ich nicht so hin, zumindest sieht es murksig aus aber ihr wisst ja was gemeint ist.
PIN # USAGE
1. DATA = lila
2. COMMAND = orange
3. N/C (9 Volts unused) = ------
4. GND = schwarz
5. VCC = rot
6. ATT = gelb
7. CLOCK = blau
8. N/C = ------
9. ACK = grün
original playstation eins pad. also kabel farbe und funktion.
LOOKING AT THE PLUG
-------------------------------
PIN 1->| o o o | o o o | o o o |
\__________________/
das mit dem bild bekomme ich nicht so hin, zumindest sieht es murksig aus aber ihr wisst ja was gemeint ist.
PIN # USAGE
1. DATA = lila
2. COMMAND = orange
3. N/C (9 Volts unused) = ------
4. GND = schwarz
5. VCC = rot
6. ATT = gelb
7. CLOCK = blau
8. N/C = ------
9. ACK = grün